sudo smartctl --xall /dev/sdc
YubiKey for `pizzaman':
smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.13.6-arch1-1] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: SAMSUNG SpinPoint F1 DT
Device Model: SAMSUNG HD753LJ
Serial Number: S13UJDWQ733069
LU WWN Device Id: 5 0000f0 003370396
Firmware Version: 1AA01113
User Capacity: 750,156,374,016 bytes [750 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA/ATAPI-7, ATA8-ACS T13/1699-D revision 3b
Local Time is: Wed Sep 1 21:19:24 2021 AEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Disabled
APM feature is: Disabled
Rd look-ahead is: Enabled
Write cache is: Enabled
DSN feature is: Unavailable
ATA Security is: Disabled, frozen [SEC2]
Wt Cache Reorder: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 114) The previous self-test completed having
the read element of the test failed.
Total time to complete Offline
data collection: (11104) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 186) minutes.
Conveyance self-test routine
recommended polling time: ( 20) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-- 092 070 051 - 7928
3 Spin_Up_Time POS--- 075 075 011 - 8230
4 Start_Stop_Count -O--CK 094 094 000 - 6409
5 Reallocated_Sector_Ct PO--CK 020 020 010 - 3508
7 Seek_Error_Rate POSR-- 100 099 051 - 56
8 Seek_Time_Performance P-S--K 100 100 015 - 10038
9 Power_On_Hours -O--CK 081 081 000 - 93544
10 Spin_Retry_Count PO--CK 100 100 051 - 0
11 Calibration_Retry_Count -O--C- 099 099 000 - 1072
12 Power_Cycle_Count -O--CK 097 097 000 - 2920
13 Read_Soft_Error_Rate -OSR-- 094 078 000 - 5806
183 Runtime_Bad_Block -O--CK 100 100 000 - 69
184 End-to-End_Error PO--CK 100 100 099 - 0
187 Reported_Uncorrect -O--CK 100 100 000 - 11627
188 Command_Timeout -O--CK 100 100 000 - 0
190 Airflow_Temperature_Cel -O---K 056 037 000 - 44 (Min/Max 41/46)
194 Temperature_Celsius -O---K 056 037 000 - 44 (Min/Max 41/49 #10741)
195 Hardware_ECC_Recovered -O-RC- 100 100 000 - 13216014
196 Reallocated_Event_Count -O--CK 093 093 000 - 293
197 Current_Pending_Sector -O--C- 081 077 000 - 811
198 Offline_Uncorrectable ----CK 100 100 000 - 1
199 UDMA_CRC_Error_Count -OSRCK 099 099 000 - 2
200 Multi_Zone_Error_Rate -O-R-- 099 092 000 - 2229
201 Soft_Read_Error_Rate -O-R-- 109 069 000 - 6398
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 2 Comprehensive SMART error log
0x03 GPL R/O 2 Ext. Comprehensive SMART error log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 2 Extended self-test log
0x09 SL R/W 1 Selective self-test log
0x10 GPL R/O 1 NCQ Command Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (2 sectors)
Device Error Count: 8388 (device log contains only the most recent 8 errors)
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 8388 [3] occurred at disk power-on lifetime: 28002 hours (1166 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
00 -- 42 00 00 00 00 44 d1 e3 36 40 00 at LBA = 0x44d1e336 = 1154605878
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 00 00 d1 e3 30 40 00 13:41:49.150 READ FPDMA QUEUED
ef 00 10 00 02 00 00 00 00 00 00 a0 08 13:41:49.150 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 00 00 00 00 00 e0 08 13:41:49.150 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 00 00 00 00 00 a0 08 13:41:49.140 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 08 13:41:49.140 SET FEATURES [Set transfer mode]
Error 8387 [2] occurred at disk power-on lifetime: 28002 hours (1166 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
00 -- 42 00 00 00 00 44 d1 e3 36 40 00 at LBA = 0x44d1e336 = 1154605878
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 00 00 d1 e3 30 40 00 13:41:47.280 READ FPDMA QUEUED
ef 00 10 00 02 00 00 00 00 00 00 a0 08 13:41:47.280 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 00 00 00 00 00 e0 08 13:41:47.280 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 00 00 00 00 00 a0 08 13:41:47.270 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 08 13:41:47.270 SET FEATURES [Set transfer mode]
Error 8386 [1] occurred at disk power-on lifetime: 28002 hours (1166 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
00 -- 42 00 00 00 00 44 d1 e3 36 40 00 at LBA = 0x44d1e336 = 1154605878
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 00 00 d1 e3 30 40 00 13:41:45.530 READ FPDMA QUEUED
ef 00 10 00 02 00 00 00 00 00 00 a0 08 13:41:45.530 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 00 00 00 00 00 e0 08 13:41:45.530 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 00 00 00 00 00 a0 08 13:41:45.520 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 08 13:41:45.520 SET FEATURES [Set transfer mode]
Error 8385 [0] occurred at disk power-on lifetime: 28002 hours (1166 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
00 -- 42 00 00 00 00 44 d1 e3 35 40 00 at LBA = 0x44d1e335 = 1154605877
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 00 00 d1 e3 30 40 00 13:41:43.510 READ FPDMA QUEUED
60 00 00 00 08 00 00 00 d1 e3 28 40 00 13:41:43.510 READ FPDMA QUEUED
60 00 00 00 08 00 00 00 d1 e3 20 40 00 13:41:43.510 READ FPDMA QUEUED
60 00 00 00 08 00 00 00 d1 e3 18 40 00 13:41:43.510 READ FPDMA QUEUED
60 00 00 00 08 00 00 00 d1 e3 10 40 00 13:41:43.510 READ FPDMA QUEUED
Error 8384 [7] occurred at disk power-on lifetime: 28002 hours (1166 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
00 -- 42 00 00 00 00 44 d1 df 00 40 00 at LBA = 0x44d1df00 = 1154604800
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 00 00 d1 df 00 40 00 13:41:41.670 READ FPDMA QUEUED
ef 00 10 00 02 00 00 00 00 00 00 a0 08 13:41:41.670 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 00 00 00 00 00 e0 08 13:41:41.670 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 00 00 00 00 00 a0 08 13:41:41.670 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 08 13:41:41.670 SET FEATURES [Set transfer mode]
Error 8383 [6] occurred at disk power-on lifetime: 28002 hours (1166 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
00 -- 42 00 00 00 00 44 d1 df 00 40 00 at LBA = 0x44d1df00 = 1154604800
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 00 00 d1 df 00 40 00 13:41:39.930 READ FPDMA QUEUED
ef 00 10 00 02 00 00 00 00 00 00 a0 08 13:41:39.930 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 00 00 00 00 00 e0 08 13:41:39.930 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 00 00 00 00 00 a0 08 13:41:39.920 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 08 13:41:39.920 SET FEATURES [Set transfer mode]
Error 8382 [5] occurred at disk power-on lifetime: 28002 hours (1166 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
00 -- 42 00 00 00 00 44 d1 df 00 40 00 at LBA = 0x44d1df00 = 1154604800
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 00 00 d1 df 00 40 00 13:41:38.210 READ FPDMA QUEUED
60 00 00 00 08 00 00 00 d1 e0 90 40 00 13:41:38.210 READ FPDMA QUEUED
60 00 00 00 08 00 00 00 d1 e0 88 40 00 13:41:38.210 READ FPDMA QUEUED
60 00 00 00 08 00 00 00 d1 e0 80 40 00 13:41:38.210 READ FPDMA QUEUED
60 00 00 00 08 00 00 00 d1 e0 78 40 00 13:41:38.210 READ FPDMA QUEUED
Error 8381 [4] occurred at disk power-on lifetime: 28002 hours (1166 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
00 -- 42 00 00 00 00 44 d1 df 00 40 00 at LBA = 0x44d1df00 = 1154604800
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 00 00 d1 df 00 40 00 13:41:36.320 READ FPDMA QUEUED
ef 00 10 00 02 00 00 00 00 00 00 a0 08 13:41:36.320 SET FEATURES [Enable SATA feature]
27 00 00 00 00 00 00 00 00 00 00 e0 08 13:41:36.320 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 00 00 00 00 00 a0 08 13:41:36.320 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 08 13:41:36.320 SET FEATURES [Set transfer mode]
SMART Extended Self-test Log Version: 0 (2 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed: read failure 20% 28008 1153772108
# 2 Short offline Aborted by host 20% 21574 -
# 3 Short offline Aborted by host 20% 21574 -
SMART Selective self-test log data structure revision number 0
Note: revision number not 1 implies that no selective self-test has ever been run
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 2
SCT Version (vendor specific): 256 (0x0100)
Device State: Active (0)
Current Temperature: 44 Celsius
Power Cycle Min/Max Temperature: --/49 Celsius
Lifetime Min/Max Temperature: --/63 Celsius
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: -4/72 Celsius
Min/Max Temperature Limit: -9/77 Celsius
Temperature History Size (Index): 128 (114)
Index Estimated Time Temperature Celsius
115 2021-09-01 19:12 44 *************************
... ..(112 skipped). .. *************************
100 2021-09-01 21:05 44 *************************
101 2021-09-01 21:06 43 ************************
102 2021-09-01 21:07 44 *************************
103 2021-09-01 21:08 43 ************************
104 2021-09-01 21:09 44 *************************
... ..( 2 skipped). .. *************************
107 2021-09-01 21:12 44 *************************
108 2021-09-01 21:13 45 **************************
109 2021-09-01 21:14 44 *************************
... ..( 4 skipped). .. *************************
114 2021-09-01 21:19 44 *************************
SCT Error Recovery Control:
Read: Disabled
Write: Disabled
Device Statistics (GP/SMART Log 0x04) not supported
Pending Defects log (GP Log 0x0c) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x000a 2 2 Device-to-host register FISes sent due to a COMRESET
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0008 2 0 Device-to-host non-data FIS retries
0x0009 2 2 Transition from drive PhyRdy to drive PhyNRdy
0x000b 2 0 CRC errors within host-to-device FIS
0x000d 2 0 Non-CRC errors within host-to-device FIS
0x000f 2 0 R_ERR response for host-to-device data FIS, CRC
0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC
0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC